[Free] 2018(May) Dumps4cert Braindumps VMware VCPN610 Dumps with VCE and PDF Download 61-70

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 May VMware Official New Released VCPN610
100% Free Download! 100% Pass Guaranteed!

VMware Certified Professional – Network Virtualization

Question No: 61

Which statement is true regarding an NSX Edge gateway device configured with a DNS Server?

  1. The NSX Edge will forward all DNS requests from virtual machines sent to it to the DNS Server.

  2. The NSX Edge configuration will override the DNS Server configured by the NSX Manager.

  3. The NSX Edge registers the DNS Server with the NSX Controller.

  4. The NSX Edge periodically synchronizes its DNS tables with the primary DNS Server.

Answer: A

Question No: 62

An NSX Edge Service Gateway has two interfaces:

  • Internal interface named Internal Access

    – IP address = 10.10.10.1

    – Network mask = 255.255.255.0

  • Uplink interface named Physical Uplink

– IP address = 20.20.20.1

– Network mask = 255.255.255.0

A vSphere administrator wants to add a SNAT rule to allow traffic from the internal network segment to access external resources via the uplink interface.

Which three steps should the vSphere administrator do to add the SNAT rule? (Choose three)

  1. Apply the SNAT rule to the Internal Access interface.

  2. Select 10.10.10.1 as the translated source IP.

  3. Apply the SNAT rule on the Physical Uplink interface.

  4. Select 10.10.10.0/24 as the original subnet.

  5. Choose 20.20.20.2 as the translated source IP.

Answer: C,D,E

Question No: 63

An administrator manages a TFTP server virtual machine that is connected to a Logical Switch with a VNI of 7321. The TFTP server has been configured to use port 1069. An NSX Edge Service Gateway is connected to VNI 7321 and has an uplink interface with access to the physical network. Assume external users can reach the Service Gateway.

What should the administrator configure to ensure external connections to the TFTP server are successful?

  1. Create a DNAT rule with the original port of 69 and translated port of 1069.

  2. Create a SNAT rule with the original port of 1069 and translated port of 69.

  3. Create a SNAT rule with the original port of 69 and translated port of 1069.

  4. Create a DNAT rule with the original port of 1069 and translated port of 69.

Answer: A

Question No: 64

Which two actions take place when an active NSX Edge instance fails? (Choose two.)

  1. Once the original NSX Edge instance is recovered, it preempts the other NSX Edge instance and takes over the active role.

  2. The standby NSX Edge instance becomes the active instance and requests routing updates from the routing neighbors.

  3. Once the original NSX Edge instance is recovered, the NSX Manager attempts to place it on a different host from the other NSX Edge instance.

  4. The standby NSX Edge instance becomes the active instance and retains any routing neighbor adjacencies.

Answer: C,D

Question No: 65

Which two statements are true regarding NSX High Availability? (Choose two.)

  1. NSX HA is configured as Active-Active.

  2. NSX HA is configured as Active-Standby.

  3. If an Active node fails, there is no service interruption during failover.

  4. If an Active node fails, there is a 15 second service interruption during failover.

Answer: B,C

Question No: 66

Where does the Distributed Logical Firewall enforce firewall rules?

  1. At the Virtual Machine#39;s virtual Network Interface Card (vNIC).

  2. At the Logical Switch virtual port that the Virtual Machine connects to.

  3. At the NSX Controller#39;s firewall kernel module.

  4. At the ESXi host vmnic used by the vSphere Distributed Switch.

Answer: A

Question No: 67

How are Logical Firewall rules applied to affected virtual machines?

  1. They are pushed by the NSX Controllers into all the ESXi hosts in the same Transport Zone.

  2. They are pushed by the NSX Manager to the ESXi hosts running the source and/or destination virtual machines.

  3. They are pushed by the NSX Controllers to the ESXi hosts running the destination virtual machines.

  4. They are pushed by the NSX Manager to all the ESXi hosts in the NSX environment.

Answer: B

Question No: 68

An administrator wishes to control traffic flow between two virtual machines. The virtual machines are in the same subnet, but are located on separate ESXi hosts.

The administrator deploys an Edge Firewall to one of the hosts and verifies the default firewall rule is set to deny, but the two virtual machines can still communicate with each other.

What task will correct this issue?

  1. Configure both ESXi host firewalls to deny traffic from the virtual machine on the other host.

  2. Deploy another Edge Firewall on the host running the second virtual machine.

  3. Remove any other firewall appliances that may exist on either of the ESXi hosts.

  4. Deploy a Distributed Firewall with firewall rules to prevent traffic between the virtual machines.

Answer: D

Question No: 69

An administrator has deployed NSX in an environment containing a mix of vSphere 5 hosts. The implementation includes the Distributed Firewall Service, but the administrator finds that rules are not being applied to all affected virtual machines.

What two conditions would cause this behavior? (Choose two.)

  1. Some hosts have not been prepared for NSX.

  2. Only ESXi 5.5 and later hosts can push the rules to the virtual machines.

  3. Only ESXi 5.1 and later hosts can push the rules to the virtual machines.

  4. Some hosts are blocking the port used for rule distribution.

Answer: A,C

Question No: 70

An administrator wants to perform Activity Monitoring on a large group of virtual machines in an NSX environment. How would this task be accomplished with minimal administrative effort?

  1. Create a PowerCLI script to enable virtual machine data collection on each virtual machine.

  2. Create a security group in Service Composer and add the virtual machines to the security group.

  3. Add the virtual machines to the pre-defined Activity Monitoring security group in Service Composer.

  4. Add the virtual machines to a VM folder in vCenter Server and enable data collection.

Answer: C

100% Dumps4cert Free Download!
Download Free Demo:VCPN610 Demo PDF
100% Dumps4cert Pass Guaranteed!
Download 2018 Dumps4cert VCPN610 Full Exam PDF and VCE

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.