Networking with Windows Server 2016
Question No: 21 DRAG DROP
You have an internal network that contains multiple subnets.
You have a Microsoft Azure subscription that contains multiple virtual networks.
You need to deploy a hybrid routing solution between the network and the Azure subscription. The solution must ensure that the computers on all of the networks can connect to each other.
You install RAS Gateway and enable BGP routing on the network and in Azure.
Which three actions should you perform next in sequence? To answer, move the appropriate actions from the list of actions to the answer area and arrange them in the correct order.
Question No: 22
Note: This question is part of a series of questions that use the same scenario. For your convenience, the scenario is repeated in each question. Each question presents a different goal and answer choices, but the text of the scenario is exactly the same in each question in this series.
Your network contains an Active Directory domain named contoso.com. The functional level of the domain is Windows Server 2012.
The network uses an address space of 192.168.0.0/16 and contains multiple subnets. The network is not connected to the Internet.
The domain contains three servers configured as shown in the following table.
Client computers obtain TCP/IP settings from Server3.
You add a second network adapter to Server2. You connect the new network adapter to the Internet. You install the Routing role service on Server2.
Server1 has four DNS zones configured as shown in the following table.
What should you do to enable Server2 as a NAT server?
From Routing and Remote Access, add an interface.
From Windows PowerShell, run the New-RoutingGroupConnector cmdlet.
From Routing and Remote Access, add a routing protocol.
From Windows PowerShell, run the Install-WindowsFeature cmdlet.
Question No: 23
Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution. Determine whether the solution meets the stated goals.
Refer to exhibit:
Server1 has two virtual machines named VM1 and VM that run Windows Server 2016. VM1 connects to Private VM2 has two network adapters.
You need to ensure that VM1 connects to the corporate network by using NAT.
Solution: You connect VM2 to private1 and External1. You run the New-NetNatIpAddress and the New-NetNat cmdlets on VM2. You configure VM1 to use VM2 as the default gateway.
Does this meet the goal?
Question No: 24
You have a DHCP server named Server1.
Server1 has an IPv4 scope that contains 100 addresses for a subnet named Subnet! Subnet1 provides guest access to the Internet. There are never more than 20 client computers on Subnet1 simultaneously; however, the computers that connect to Subnet 1 are rarely the same computers.
You discover that some client computers are unable to access the network. The computers that have the issue have IP addresses in the range of 169.254.0.0/16.
You need to ensure that all of the computers can connect successfully to the network to access the Internet.
What should you do?
Create a new scope that uses IP addresses in the range of 169.254.0.0/16.
Modify the scope options.
Modify the lease duration.
Configure Network Access Protection (NAP) integration on the existing scope.
Question No: 25
You have a DHCP server named Server1 that runs Windows Server 2016. You have a single IP subnet.
Server1 has an IPv4 scope named Scope1. Scope1 has an IP address range of 10.0.1.10 to 10.0.1.200 and a length of 24 bits.
You need to create a second logical IP network on the subnet. The subnet will use an IP address range of 10.0.2.10 to 10.0.2.200 and a length of 24 bits.
What should you do?
Create a second scope, and then create a superscope.
Create a superscope, and then configure an exclusion range in Scope1.
Create a new scope, and then modify the IPv4 bindings.
Create a second scope, and then run the DHCP Split-Scope Configuration Wizard.
Question No: 26
Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution that might meet the stated goals. Some questions sets might have more than one correct solutions, while others might not have a correct solution.
After you answer a question in this section, you will NOT be able to return to it. As a result, these questions will not appear in the review screen.
Your network contains an Active Directory forest named contoso.com. The forest has three sites located in London, Paris and Berlin.
The London site contains a web server named Web1 that runs Windows Server 2016.
You need to configure Web1 as an HTTP content server for the hosted cache servers located in the Paris and Berlin sites.
Solution: You install the DFS Replication role service, and then you start the Network Connections service.
Does this meet the goal?
Question No: 27 HOTSPOT
You have a Hyper-V host named Server1 that runs Windows Server 2016. Server1 connects to your corporate network. The Corporate network uses the 10.10.0.0/16 address space.
Server1 hosts a virtual machine named VM1, VM1 is configured to have an IP addresses of 172.16.1.54/16.
You need to ensure that VM1 can access the resources on the corporate network. What should you do? To answer, select the appropriate options in the answer area.
Question No: 28 HOTSPOT
Your network contains an Active Directory domain named contoso.com. The domain contains a domain-based Distributed File System (DFS) namespace named Namespace1.
You need to view the shares to which users will be redirected when the users attempt to connect to a folder named Folder1 in the DFS namespace.
What cmdlet should you run? To answer, select the appropriate options in the answer area.
Question No: 29
Your network contains three subnets, a production subnet that contains production servers, a development network that contains development servers, and a client network that contains client computers.
The development network is used to test applications and reproduces servers that are located on the production network. The development network and the production network use the same IP address range.
A developer has a client computer on the client network. The developer reports that when he attempts to connect to the IP address 10.10.1.6 from his computer, he connects to a server on the production network.
You need to ensure that when the developer connects to 10.10.1.6, he connects to a sever on the development network
Which cmdlet should you use?
Question No: 30
Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution that might meet the stated goals. Some question sets might have more than one correct solution, while others might not have a correct solution.
After you answer a question in this sections, you will NOT be able to return to it. As a result, these questions will not appear in the review screen.
You network contains an Active Directory domain named contoso.com. The domain contains a DHCP server named Server1. All client computers run Windows 10 and are configured as DHCP clients.
Your helpdesk received calls today from users who failed to access the network from their Windows 10 computer.
You open the DHCP console as shown in the exhibit. (Click the Exhibit button.)
You need to ensure that all of the Windows 10 computers can receive a DHCP lease. Solution: You start the DHCP Server service.
Does this meet the goal?
Answer: B Explanation:
100% Ensurepass Free Download!
–Download Free Demo:70-741 Demo PDF
100% Ensurepass Free Guaranteed!
–Download 2018 EnsurePass 70-741 Full Exam PDF and VCE
|Lowest Price Guarantee||Yes||No||No|
|Free VCE Simulator||Yes||No||No|