[Free] 2018(June) Dumps4cert Cisco 210-065 Dumps with VCE and PDF Download 171-180

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 May Cisco Official New Released 210-065
100% Free Download! 100% Pass Guaranteed!

Implementing Cisco Video Network Devices v1.0

Question No: 171 – (Topic 5)

A voice engineer installed and configured Cisco TMSXE in a Windows Server and integrated with Cisco TMS. Which action can now be taken?

  1. Use Windows PC as a Cisco TelePresence endpoint.

  2. Start Cisco TelePresence meetings online.

  3. Schedule Cisco TelePresence meetings through Outlook.

  4. Start Cisco TelePresence meetings with Cisco TelePresence endpoints.

Answer: C

Question No: 172 – (Topic 5)

When outside of the network, Cisco Jabber uses which of the following DNS SRV records

to complete service discovery and reach domain.com?

  1. _cuplogin._tcp.domain.com DNS SRV record

  2. _xmpp-server._tcp.domain.com DNS SRV record

  3. _cisco-uds._tcp.domain.com DNS SRV record

  4. _collab-edge._tls.domain.com DNS SRV record

Answer: D

Question No: 173 – (Topic 5)

Which three features are supported by the Cisco Video Surveillance Encoding Server? (Choose three.)

  1. IP and analog cameras

  2. MPEG-2 and MPEG-4 encoding

  3. archiving

  4. motion detection

  5. clustering

  6. virtual matrix

Answer: A,C,D

Question No: 174 – (Topic 5)

The command xCommand Security FIPSMode Activate is issued to a Cisco TelePresence C-Series codec. Management wants to reverse the effects of this command. Which two methods could be used for this purpose? (Choose two.)

  1. From the touch screen, disable FIPS mode in the Administrator Settings menu.

  2. From the touch screen, perform a factory reset from the Administrator Settings menu.

  3. From the touch screen, disable all security settings from the Administrator Settings menu.

  4. Use SSH to connect to the system and enter the xCommand Security FIPSMode Deactivate command.

  5. Use Telnet to connect to the system and enter the xCommand SystemUnit FactoryReset Init command.

  6. Use SSH to connect to the system and enter the xCommand SystemUnit FactoryReset Confirm: Yes command.

Answer: B,F

Question No: 175 – (Topic 5)

A video engineer needs to locate the running version of the Cisco VCS. Which tab contains this information?

  1. System

  2. Applications

  3. Configuration

  4. Status

Answer: D

Question No: 176 – (Topic 5)

Refer to the exhibit.

Dumps4Cert 2018 PDF and VCE

The numbers on the floor plan represent the horizontal average lux readings for nine

different room areas. Considering Cisco best practices, what can you conclude about the lighting conditions?

  1. Only three areas meet the room lighting levels that are recommended by Cisco.

  2. Only three areas do not meet the room lighting levels that are recommended by Cisco.

  3. All areas meet the room lighting levels that are recommended by Cisco.

  4. The areas do not meet the room lighting levels that are recommended by Cisco.

Answer: B

Question No: 177 – (Topic 5)

Which MCU supports the use of a lobby screen?

  1. CTMS

  2. TS 8710

  3. MCU 5300

  4. Conductor

Answer: B

Question No: 178 – (Topic 5)

Which two methods can be used to set the default call protocol of a Cisco TelePresence endpoint running TelePresence codec firmware? (Choose two.)

  1. Use the GUI and set System gt; H.323 gt; Settings gt; Default Call Protocol gt; H.323.

  2. Use the CLI command xConfiguration Conference 1 DefaultCall Protocol: H323.

  3. Use the CLI command Conference Default Protocol: H323.

  4. Use the CLI command Default Protocol: H323.

  5. Use the GUI and set Configuration gt; System Configuration gt; Conference gt; DefaultCall gt; H.323.

Answer: B,E

Question No: 179 – (Topic 5)

In a Cisco TelePresence MX300 G2, what is the minimum bandwidth for 1080p30?

  1. 768 kbps

  2. 1152 kbps

  3. 1472 kbps

  4. 1873 kbps

  5. 2560 kbps

Answer: C

Question No: 180 – (Topic 5)

In this item, you will need to use all information presented to you to successfully answer the question.

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

The C-Series endpoint (codec) does not register with the Video Communication Server that is located in a different network. Based on the exhibits, what could be causing the issue?

  1. The subnet mask on the codec is incorrect.

  2. The ip address of the codec is incorrect.

  3. The interface that the codec is in is in the wrong VLAN.

  4. The codec did not receive a DHCP address from the DHCP server.

Answer: A Explanation:

The subnet mask configured on the codec is 255.255.255.128, when it should be 255.255.255.0.

100% Dumps4cert Free Download!
Download Free Demo:210-065 Demo PDF
100% Dumps4cert Pass Guaranteed!
Download 2018 Dumps4cert 210-065 Full Exam PDF and VCE

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.