[Free] 2018(Aug) Ensurepass Cisco 210-065 Dumps with VCE and PDF 211-220

Ensurepass.com : Ensure you pass the IT Exams
2018 Aug Cisco Official New Released 210-065
100% Free Download! 100% Pass Guaranteed!

Implementing Cisco Video Network Devices v1.0

Question No: 211 – (Topic 5)

Which two additional items can be configured for an endpoint to register with the Cisco

TelePresence Video Communication Server for H.323 to function correctly? (Choose two.)

  1. unique system ID

  2. unique H.323 ID

  3. unique DNS entry ID

  4. unique E.164 alias

  5. unique real-time transport protocol port numbers

  6. unique NTP server IPv4 address

Answer: B,D

Question No: 212 – (Topic 5)

A Cisco engineer needs to provide digital media for the lobby of a company. Which Cisco Digital Media component should the engineer use?

  1. Cisco Cast

  2. Cisco Digital Signs

  3. Cisco DMP

  4. Cisco Show and Share

  5. Cisco IP TV

Answer: B

Question No: 213 – (Topic 5)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

Acoustic measurements for ambient noise were taken on a candidate for an Immersive Cisco TelePresence room. The numbers on the floor plan represent the dBA readings for each of the six areas of the room.

Considering Cisco best practices, what can you conclude about the current acoustic situation in the room?

  1. Only one area is within the noise levels that are recommended by Cisco.

  2. Only one area is not within the noise levels that are recommended by Cisco.

  3. All areas are within the noise levels that are recommended by Cisco.

  4. Two areas are within the noise levels that are recommended by Cisco.

Answer: A

Question No: 214 – (Topic 5)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

Which tab can be used in order to check the call statistics for the Cisco TelePresence Codec C60?

  1. Diagnostics

  2. Configuration

  3. Call Control

  4. Maintenance

  5. The GUI cannot be used to view call statistics.

Answer: C

Question No: 215 – (Topic 5)

How would an administrator reset a Cisco VCS Control appliance to the default configuration?

  1. Via the CLI, log in as root and issue the factory-reset command.

  2. Via the CLI, log in as root and issue the reset-defaults command.

  3. Via the web GUI, log in as the administrator, choose Backup and Restore, and click the Factory Reset button.

  4. Hold down the power button for 10 seconds until the light flashes.

  5. Hold down the reset button on the back of the appliance for 10 seconds.

Answer: A

Question No: 216 – (Topic 5)

A Cisco TelePresence EX Series desktop endpoint failed to register to a Cisco VCS. The SIP status shows quot;Failed: 403 Forbiddenquot; in the endpoint#39;s web interface. What is the first thing that should be checked in the endpoint configuration settings?

  1. Verify that the correct SIP authentication credentials have been configured.

  2. Ensure that CallSetup Mode is set to Gatekeeper.

  3. Verify that Outbound Connection Credentials are properly configured.

  4. Check to see that SIP Mode is set to On.

Answer: A

Question No: 217 – (Topic 5)

A user is currently on a Cisco TelePresence call using a Touch 8 device and would like to change the local screen layout so that the active speaker is in full screen and the other participants are smaller within the picture. Which layout option should the user choose?

  1. Prominent

  2. Overlay

  3. PiP

  4. FullScreen

Answer: B

Question No: 218 – (Topic 5)

Which two actions must take place for proper operation when using Advanced Networking on Cisco VCS? (Choose two )

  1. Automatic routing must be enabled

  2. NAT reflection must be enabled on the firewall

  3. Manual routes must be added using xCommand RouteAdd

  4. Network interfaces must reside in the same subnet

  5. Network interfaces must reside in separate subnets

Answer: C,E

Question No: 219 – (Topic 5)

A user is unable to make a video call from an endpoint that is registered to the Cisco VCS. To isolate the cause, which two menu choices should the user check first? (Choose two.)

  1. Configuration gt; Call Policy

  2. Status gt; Registrations

  3. Status gt; Search History

  4. Status gt; System Information

  5. Configuration gt; Dial Plan gt; Search Rules

  6. Status gt; Event Log

Answer: C,F

Question No: 220 – (Topic 5)

Which path should you follow to initiate a Cisco Telepresence System 1310-65 camera calibration procedure?

  1. Troubleshooting gt; Hardware Setup gt; Setup gt; Show Focus Target

  2. Troubleshooting gt; Hardware Setup gt; Cameras gt; Setup gt; Calibrate

  3. Hardware Setup gt; Start gt; Cameras gt; Setup gt; Show Focus Target

  4. Troubleshooting gt; Hardware Setup gt; Cameras gt; Show Camera Target

Answer: D

100% Ensurepass Free Download!
210-065 PDF
100% Ensurepass Free Guaranteed!
210-065 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.